Brief description:
1. Heat exchanger
2. Can be customerized
3. Work Pressure: 0.2~3.1MPa
4. Fin space: 1.2~3.5mm
5. Tube Diameter: 7, 9.52, 12.7, 16mm
The technology to create perfection:
1. The fins produced are of vry high standard of quality having flare position made of plain,
Wave type.
2. The edge of fins can be straight or ripple depending upon application.
3. All the coils are 100% tested for leakages and passed through the heating oven with ht air circulation for inside and ourtside cleaning and charged nitrogen.
4. The mechanical bullet expansion of copper tube to fin ensures efficient heat transfer of co-densers and evaporators.
5. The row material of excellence: We source only the best quality raw material from aroud the world, , to manufacture heat exchangers that are of globally acceptable standards.
6. Plain copper pipe of 7mm, 7.94mm, 9.52mm and 12.75mm diameter.
7. Aluminum foil in blu color with hydrophilic and bio(Health) properties.
Features:
1. Material: Copper, aluminum, galvanized plate
2. Aluminum foil: Hydrophilic or bare
3. Fin type: Louver fin or flat fin or corrugated fin
4. Copper pipe: Diameter 7mm or 8mm or 9.52mmor 12.75mm or 15.888mm, grooved or smooth tube
5. Pitch of fins can be adjusted between 1.8- 5.8mm.
6. Pitch of holes and pitch of rows: 25*21.65MM and 12.7*19.05MM
7. Suitable for R134A, R22, R404A, R407C refrigerant and so on
8. Voltage: 220V/1/50Hz and 380V/3/50Hz or other type.
9. Different alternative condensing fans available: Shaded pole or outer rotor fan motor.
10. Did gas examination under 3.0Mpa air pressure to ensure the tightness.
11. Widely used in refrigeration industry, cold room and other cooling system.
12. We can supply products as per customized samples or drawing.
13. Producing procedure: Tube bending, punching fin, expanding, digressing, drying
Welding, leakage test, bending, inspection, packing
Note: For further information please contact us
| Item | heat exchangers type | Operation medium | Operation pressure ( MPa ) |
Application |
| 1 | Φ 16/Φ 9.52/Φ 12.7 Copper tube with aluminium fin |
Cold/hot water | ≤ 1.6 | Used for combined air handling unit, fan coil etc air conditioning devices |
| 2 | Φ 18/Φ 20 Steel pipe winding with steel sheet |
Steam | ≤ 0.2 | Used for combined air handling unit, fan coil etc air conditioning devices |
| 3 | Φ 16/Φ 9.52/Φ 12.7 Copper tube with aluminium fin |
Brine | ≤ 1.6 | Used for heat transfer in cold storage and all kinds of low temperature systems |
| 4 | Φ 9.52/Φ 7.94/Φ 7 Copper tube with aluminium fin |
Ethylene glycol | ≤ 1.6 | Used of energy recovery and low temperature system devices |
| 5 | Φ 16 Copper tube with aluminium fin |
Ice mud | ≤ 1.6 | Used for dry operation condition, fresh air dehumidification etc systems |
| 6 | Φ 9.52/Φ 7.94/Φ 7 Copper tube with aluminium fin |
R22 | ≤ 1.9 | Used for industry and commerce air conditioning system |
| 7 | Φ 9.52/Φ 7.94/Φ 7 Copper tube with aluminium fin |
R407C | ≤ 1.9 | Used for industry and commerce air conditioning system |
| 8 | Φ 9.52/Φ 7.94/Φ 7 Copper tube with aluminium fin |
R134a | ≤ 3.1 | Used for vehicle and vessel etc transportation devices |
ote: for further information please contact me.
Ms. Echo Lee
Tel: +86 21 35324169-206Â
Mob: +86 18217219074
Â
Â
 Fin Heat Exchangers for Commercial AC (FP)
Brief description:
1. Heat exchanger
2. Can be customerized
3. Work Pressure: 0.2~3.1MPa
4. Fin space: 1.2~3.5mm
5. Tube Diameter: 7, 9.52, 12.7, 16mm
The technology to create perfection:
1. The fins produced are of vry high standard of quality having flare position made of plain,
Wave type.
2. The edge of fins can be straight or ripple depending upon application.
3. All the coils are 100% tested for leakages and passed through the heating oven with ht air circulation for inside and ourtside cleaning and charged nitrogen.
4. The mechanical bullet expansion of copper tube to fin ensures efficient heat transfer of co-densers and evaporators.
5. The row material of excellence: We source only the best quality raw material from aroud the world, , to manufacture heat exchangers that are of globally acceptable standards.
6. Plain copper pipe of 7mm, 7.94mm, 9.52mm and 12.75mm diameter.
7. Aluminum foil in blu color with hydrophilic and bio(Health) properties.
Features:
1. Material: Copper, aluminum, galvanized plate
2. Aluminum foil: Hydrophilic or bare
3. Fin type: Louver fin or flat fin or corrugated fin
4. Copper pipe: Diameter 7mm or 8mm or 9.52mmor 12.75mm or 15.888mm, grooved or smooth tube
5. Pitch of fins can be adjusted between 1.8- 5.8mm.
6. Pitch of holes and pitch of rows: 25*21.65MM and 12.7*19.05MM
7. Suitable for R134A, R22, R404A, R407C refrigerant and so on
8. Voltage: 220V/1/50Hz and 380V/3/50Hz or other type.
9. Different alternative condensing fans available: Shaded pole or outer rotor fan motor.
10. Did gas examination under 3.0Mpa air pressure to ensure the tightness.
11. Widely used in refrigeration industry, cold room and other cooling system.
12. We can supply products as per customized samples or drawing.
13. Producing procedure: Tube bending, punching fin, expanding, digressing, drying
Welding, leakage test, bending, inspection, packing
Note: For further information please contact us
| Item | heat exchangers type | Operation medium | Operation pressure ( MPa ) |
Application |
| 1 | Φ 16/Φ 9.52/Φ 12.7 Copper tube with aluminium fin |
Cold/hot water | ≤ 1.6 | Used for combined air handling unit, fan coil etc air conditioning devices |
| 2 | Φ 18/Φ 20 Steel pipe winding with steel sheet |
Steam | ≤ 0.2 | Used for combined air handling unit, fan coil etc air conditioning devices |
| 3 | Φ 16/Φ 9.52/Φ 12.7 Copper tube with aluminium fin |
Brine | ≤ 1.6 | Used for heat transfer in cold storage and all kinds of low temperature systems |
| 4 | Φ 9.52/Φ 7.94/Φ 7 Copper tube with aluminium fin |
Ethylene glycol | ≤ 1.6 | Used of energy recovery and low temperature system devices |
| 5 | Φ 16 Copper tube with aluminium fin |
Ice mud | ≤ 1.6 | Used for dry operation condition, fresh air dehumidification etc systems |
| 6 | Φ 9.52/Φ 7.94/Φ 7 Copper tube with aluminium fin |
R22 | ≤ 1.9 | Used for industry and commerce air conditioning system |
| 7 | Φ 9.52/Φ 7.94/Φ 7 Copper tube with aluminium fin |
R407C | ≤ 1.9 | Used for industry and commerce air conditioning system |
| 8 | Φ 9.52/Φ 7.94/Φ 7 Copper tube with aluminium fin |
R134a | ≤ 3.1 | Used for vehicle and vessel etc transportation devices |
ote: for further information please contact me.
Ms. Echo Lee
Tel: +86 21 35324169-206Â
Mob: +86 18217219074
Â
Â
Â
Plastic Injection Molding Factory.We are advanced China Plastic Injection Molding manufacturers. Our Plastic Injection Molding manufacturing methods are extremely accurate and fast. They can provide unlimited rapid prototype plastic injection molding capabilities for a wide variety of high-volume products. The method is also used for low volume, high-quality plastic parts for everything from toy cars to giant television screens. Rapid prototyping is the process of designing and creating a new product or component using plastic injection molds. It is a critical process because it helps identify new product characteristics by testing them over again before a product goes to production.Plastic injection molds allow designers and engineers to create detailed models from digital designs that can then be brought to life into a physical product. This kind of design sharing provides a tremendous advantage for companies trying to reduce product development costs.
Many rapid injection molding tools include tools that are designed to assist the manufacturer with their overall production efforts. These tools can offer you a number of additional services including computer software designed to help you streamline your production efforts and increase your profitability. By streamlining your efforts, you can expect to see a significant increase in your production rate and efficiency.
RongNa offer OEM/ODM custom rapid prototype plastic injection tooling which can help you reduce the time necessary to create new parts and can save you valuable money on material costs.
The Finishing Option For Injection Molding
.Matte
.polished,
.sprayed,
.screen printing,
.pad printing,
.thermal transfer,
.water transfer,
.laser engraving,
.electrophoresis (water plating),
.vacuum coating,
.biting (etching, skin texture) for plastic molds
Advantages Of Plastic Injection Molding From RongNa
According to the customer's requirement to choose the Rapid tooling or the common mold,multi - cavities to save costs. Dozens of material and finishing options available.
analysis before quoting, also will suggest the better design way.
send the mold desgin for checking before tooling make.
Procuring parts on demand, without MOQ.
All products are inspected before shipment.
Injection Molding,Polycarbonate Injection Molding,Custom Injection Molding,Thermoplastic Injection Molding
Ningbo Rongna Technology Co.,Ltd , https://www.prototyping-products.com