System consists of the top ring, jack, tubing system, hydraulic valve, fuel pump, control cabinet and other components.
Control cabinet with pump start and stop, hydraulic valve position, over pressure protection, jacking stroke indication and other functions. The fuel pump by the 20l tank, piston pump? The maximum pressure of 32MPa (optional working pressure 16MPa, flow 1L / min, motor power 1.5kW and other components.
Hydraulic valve with M-type hydraulic valve, model HD-3C6-G02-LW, pressure rating 60MPa.
Tubing system using DN10 × 2 seamless steel pipe, pressure rating 70MPa.
Jack used 4 sets of 60 plunger, stroke 50mm, pressure level 60MPa, a single overhead load ≥ 8t. Rotor lift height 5 ~ 8mm According to the motor structure to determine, the device is set to 7 ± 0.5mm.
The top ring is a specially designed part.
The lifting speed of the device is 15mm / min, the holding time is 5min, the falling speed is 20-30mm / min, and the method of simultaneously lifting the top of 6 sets of units also can adjust the top of a single unit as needed.
Key technical measures
1, the top ring
As the rotor flange on the outer surface of the counterweight, coupled with the actual layout of the space can not be directly jack jack jack, and thus set a top ring. Top jack lifting jack, top ring and then lift the rotor. Top ring must ensure that the requirements of the parallel rise to prevent the top. Top ring under the flange surface welding 4 ring pad, set in the jack plunger, so that the top ring positioning.
2, to prevent partial top
Each unit set 4 jack, through the top ring, jack stroke control, and the use of equal pressure oil, to ensure that the jack pressure balance, to avoid the difference between the lift and jacking caused by the top.
3, to prevent the rotor down too fast
Rotor down, in order to prevent the speed too fast, causing damage and impact thrust bearing tile surface, the throttle valve into the various types of units, easy to adjust the rotor speed down, controlled at 1 ~ 2min.
4, jack
Jacks by the full stroke limit design to prevent excessive rotor lift.
5, to prevent the tubing into the air,
The fuel tank, fuel pump placed at the highest point of the system? Motor floor ?, So as to effectively prevent the tubing system due to long-term deactivation of the intake problem.
6, hydraulic valve
When the fuel is being supplied, the jack is lifted. Reverse fuel supply, jack reset. In the middle position, the tubing system holds the jacks in place. These features meet the rotor jacking up, the need to maintain a certain time is generally 5min and forced reset after jacking requirements.
7, electrical control
1 jack stroke instructions. Each jack has a lift, reset the travel switch and indicator light in place, and with light test button, in order to check the light is normal.
2 system over-voltage protection. Equipped with pressure relief valve and pressure relief double protection. When the system pressure reaches the set value, overflow valve overflow. If the system pressure exceeds a certain range of the set value, the pressure relay action, the hydraulic valve back to the middle position, the pump stops running at the same time, over-pressure indicator light.
3 system work pressure calculation.
Jack jacking pressure:
P0 = W / nxs
Where: P0 - Jack lift kg / cm2
W - rotor weight kg
n - the number of jacks
S - jack plunger area cm2
P0 = W / nxs = 15 × 1000 / [4 × (3.1415926 / 4)] = 132.6 kg / cm 2
Pressure relief valve working pressure: PV = 1.2 ~ 1.3P0
PV should be set to meet more than three normal work jack before lifting the rotor requirements, to avoid two top-off.
Over-voltage protection relay working pressure:
PK = 1.1PV
4 power supply. Working power 220V, travel switch with 24V, in order to ensure safety.
Application prospects
The device has been successfully applied to Luo Yu pumping station 6 630KW pump rotor top rotor project, received a convenient and reliable use of the results. The device focuses on solving the actual situation that the rotor structure of the motor is irregular, the space layout is complicated and the simple lifting structure can not be used.
The device can be widely applied to the more complicated top rotor projects in the fields of water supply and drainage, electric power, chemical industry and so on, and provides references for the design and calculation of other types of top rotor devices.
Stainless Steel Cut Wire Shot AS Cut
Cut Wire Shot is a very important and popular Metal Abrasive.It is often utilized in shot peening processes when ferrous contamination of work piece is forbidden. As the most cost-effective one, the stainlesss steel cut wire shot, also named Stainless Steel Shot, is widely used for shot peening processes on stainless steel or inconel parts. When Blasting stainless work pieces or other metals need to be down as a pristine surface, stainless cut wire may be a very good metal abrasive to take into consideration. Stainless Steel Cut Wire Shot As Conditioned is usually used for shot peening processes on stainless steel or inconel parts. As for Longlived stainless steel cut wire shot, the minimum diameter could be 0.15mm and maximum diameter is 3mm. If you want, it could be bigger as your demand.
Concerning stainless steel cut wire shot, it has a very bright surface, maintains its shape longer then cast abrasives and it has a dust free surface. Stainless Steel Cut Wire is available as cut or conditioned and with various chemical compositions.The bulk density of stainless steel cut wire shot is very high and must be taken into consideration in relation to its use in equipment. Suitable equipment must be selected to convey stainless steel shot.
Generally, stainless steel cut wire shot could be classfied into two kinds. One is stainless steel cut wire shot as cut and as conditioned. And then, stainless steel cut wire shot as conditioned could also be divided into three small groups according to their different roundness and they are G1, g2, G3.
Stainless Steel Cut Wire Shot As Cut,410 Stainless Steel Cut Wire Shot As Cut,Sus304 Stainless Steel Cut Wire Shot,Sus410 Stainless Steel Cut Wire Shot As Cut
Longlived Metal Products Co ., Ltd , https://www.longlivedmetalproducts.com