Users of small suction trucks will experience some unfavorable operations when they use the suction truck. This will cause great damage to the vehicle. Now we will introduce the most basic vehicle damage.
Diligently shift gears
Many drivers of the manual transmission model are either eager to save time or because the newcomers are not used to shifting gears. Even when the vehicle speed is raised to a higher level and the vehicle does not match the speed and speed, the original gear position is not maintained. change. In fact, this low-speed, high-speed approach increases engine load and causes significant damage to the engine. Experienced old drivers have said that driving can not be lazy, shift gear according to speed.
There is a common misconception in the drive that the damage to the engine is greater, that is, upshift overtaking. When the gear is high, the torque of the engine is rather small, and the throttle response is insensitive, which does not achieve the desired acceleration effect. The correct approach is to take the initiative to lower the speed when overtaking. For automatic models
For example, when the driver steps on the gas pedal, the trip computer will automatically make a judgment, downshift to provide enough torque to overtake. But the premise is that the driver should step on the throttle deep enough.
For a long time in a semi-clutch state
Some drivers are accustomed to pressing their left foot on the clutch when driving, so that they can better maintain control of the vehicle. However, in practice, this practice is extremely damaging to the clutch. Especially when the vehicle is running at a high speed, a long half-clutch state will rapidly wear the clutch plate.
In addition, the second block start will also lead to premature clutch damage. A block start is beneficial to any vehicle.
Not completely separated on the shift
Usually we can see that some impatient owners are busy hanging gears when the clutch is not stepped on the end. Not only is the gear position difficult to hang in, but the long-term operation of this type of vehicle is a deadly problem for manual gearboxes. damage. Although there is no step-by-step change in automatic car models
The problem of blocking, but many drivers hurriedly hung on the P block when the vehicle did not completely stop, and the gearbox could not bear the situation that the vehicle condition did not match the operation.
Horse curb jumped past
It is often difficult to observe the shock absorbers, springs, and suspension of the vehicle, but they are also vulnerable parts of the vehicle. When you cross the ditch, you slow down in advance, instead of rushing the vehicle hard. This not only guarantees the comfort of the ride but also protects the shock absorber, the spring and the suspension.
Many car owners jumped up when they were on the road and wanted to show superb driving skills. But maybe one time, the vibration or spring of the vehicle will no longer match your operation.
Similarly, not overloading not only improves fuel economy, but also protects automotive components such as suspension.
Frequently operated combination switch
The flashing of vehicle lights allows owners to feel good about themselves, but they do not know that frequent switching will increase the chance of damage to the combination switch. At the instant when the switch is turned on, the current through the switch contacts is much higher than usual, and the light is ignited in a half-split half-split state, and the spark may burn the contacts.
Make the water jet forced to work
When the winter temperature is low and the water spout is frozen, do not force the water on the glass. This will only damage the water pump. The owner can wait for the vehicle to start, the vehicle temperature to come up, and the frozen water nozzle to be sprayed after it is iced.
The same is true of the wipers. The cold wipers do not achieve the desired cleaning effect and can damage the wipers themselves.
Tire tread
There are many warnings about tires, but one thing worth noting is that the tire has the thinnest side, so when the owner steps up or crosses the road, he must pay special attention to the protection of the sidewall, and do not collide with the front. Side, side of the collision than the front but also destroy the tire.
Hold down the glass lifter
Many vehicle glass electric switches do not work or the window glass cannot be lifted into place, which is also related to the mistakes of daily operations.
When using the electric glass lifter to lift the glass, when the window is lowered to the bottom or raised to the top, be sure to loosen it in time, otherwise the mechanical parts of the vehicle will be relatively strong, and the motor will naturally be destroyed.
Pulling his hand to brake
Experienced old drivers stated that they should use gears more when controlling the speed, anticipate early, diligently shift gears, and use less brakes. In particular, let the engine brake when downhill, occasionally supplemented by braking, do not step on the brake downhill, so you can protect the brake pads.
Do not forget to release your hand before starting the vehicle. Braking with your hand is the most wearable brake shoe.
Steering wheel rotation angle is too large
Because it is often used, booster pumps are also fragile components on the vehicle. In the direction of the driver, when the driver hits the head, he should return a little. Do not let the booster pump stay in a tight state for a long time, which will help to prolong the life of the booster pump.
Only the more you care about your own suction truck, then you will make your vehicle better.
Roller Shutter Door and Door Frame Forming Machine Series
Roller Shutter Door and Door Frame Forming Machine
This door frame machine is designed according to cutstomer require. One machine can produce same profile but different sizes. It saves lots of cost, and get customers great satification.
The shutter door machine has many type of design. The austrilia type use wide raw material width, and easy to make the door. The small type of shutter door strip has nice appearance, and durable product. Besides, there are some other type of shutter door machine, like anti-wind shutter door machine and fire proof shutter door machine. The fire proof shutter door machine has the steel frame with EPS inside.Such as steel door frame making machine.
Roller Shutter Door Forming Machine,Door Frame Forming Machine,Door Frame Roll Forming Machine,Shutter Door Roll Forming Machine
Botou Xianfa Roll Forming Machine Factory , https://www.rollformingmachinecn.com