The first-line raw material storage and transportation system of our company adopts Φ1.6m × 8.5m pneumatic lift pump, which is supplied by 3 Roots blowers. In this paper, the phenomenon of blocking material appeared in the use of pneumatic lift pump is analyzed and the solution is found out.
1, Roots blower fan failure
1.1, Roots blower outlet relief valve pressure setting is too small
Trial production early, with the amount of mill feed increased, appear to enhance the pump blocking material. Roots blower current value of about 65%, is a normal range, but Roots blower outlet safety valve exhaust. On-site pipeline barometer readings did not reach the safety valve emptying pressure 80kPa. Re-adjust the safety valve pressure screw, such blocking material can be ruled out.
1.2, Roots blower belt off or burning
In the V-belt wear or aging when the new triangle tension is not suitable, easy to make the V-belt off or burn. For example, the central control room screen shows a Roots blower current value dropped from about 70% of normal to no-load current 40%, while the other two Roots blower current from about 70% to 80%. In the control room did not pay attention to this alarm, switching standby Roots blower is not timely, leading to the pneumatic lift pump blocking material. The on-site inspection revealed that the safety valves on the outlet pipes of the three Roots blowers were all exhausted outward. The triangle of the first Roots blower was dropped off or burnt out, causing the motor to run idle, resulting in an increase in the current of the other two blowers. Switching to a backup Roots blower solves the problem.
1.3, Roots blower outlet check valve spool off, closing valve disc wear
Roots blower outlet check valve role is to prevent the pressure air flow back to the rotor cavity after the fan down. Globe valve pneumatic control, open before the fan motor operation, shut down after the motor shutdown, cut off the anti-channeling pressure air flow. Due to the cut-off valve wear and tear of the valve plate, resulting in pressure flow from the gap anti-channeling, impact check valve spool, a long time, resulting in spool off. The blocking phenomenon caused by such causes is as follows:
The control room screen shows three Roots blower current value from the normal value of about 70% of the peak instantly dropped to no-load current about 40%. On-site inspection of gas lift pump blocking material, but 3 Roots blower safety valve does not exhaust. Air flows from the failed Roots blower through the exhaust pipe, rotor chamber to the suction line. Stop the Roots blower, the shut-off valve is closed, the other two Roots blower current value instantly increased from 40% to 80%, safety valve exhaust.
2, pneumatic lift pump damaged canvas layer, air chamber material
After the canvas is damaged, the raw material fed into the pneumatic lift pump can not be well vaporized, reducing the conveying capacity of the pump. When the feeding amount exceeds the conveying capacity of the pump, blocking occurs. 3 Roots blower fan current values ​​are about 80%, safety valve deflated.
Approach: no need to stop immediately replaced, usually wait until the shutdown and then replace the canvas. On-site treatment may not need to open the pump body manhole door to discharge material, just open the big raw material warehouse top bag dust removal exhaust fan inlet valve, and at the same time chooses to open 3 Roots blowers to pump the material in the body to the air.
3, incoming wet caking
Due to material factors leading to the airlift pump plugging material is mainly caused by moisture, especially wet end of the humidification tower blocking material, clear down the wet material into the pneumatic lift pump by the screw conveyor, can not be vaporized away. The control room showed 3 Roots blower current values ​​are about 40% of the no-load current, the safety valve does not deflate, but the feed chute is diffuse material, percussion pump body, sound dull.
Approach: Stop raw mill system, open the pump manhole, manual shoveling, clear canvas layer and then reboot.
Table pad description editor
1, in the use of home or office environment, this product can be very good to protect your desktop and mesa, to your furniture and personal bring warm protection.
2, soft glass material resistant to high heat, cold resistant, resistant to acid, alkali, resistance to stress, anti-static, shock resistance, tensile resistance, aging resistance, good light transmission, the use of long life
Table 3, soft light, fluent writing, fast, safe and convenient access to information, help to improve banks, schools, government agencies, corporate documents processing efficiency, and to reduce the cost
4, the restaurant can reduce the cost of cleaning, add elegant appearance of the restaurant. For personal office, warm in winter and cool in summer, elastic, with flame retardant, insulation, moisture resistance, heat insulation, sound insulation, corrosion protection, anti shock, deformation, fracture, anti light, anti fade, weatherability;
5, with anti-static, in the telecommunications, electronics, computer companies, the use of precision instruments on the desktop is an essential product. Now many of the computers used by the company have been replaced by a glass desktop, with a soft glass replacement.
Table mat features
The main table mat is made of antistatic material and dissipative static material, such as rubber. The surface layer is about 0.5mm thick dissipative electrostatic layer, the bottom layer is about 1.5mm thick conductive layer. Commonly used for 2mm double layer composite structure. Table mat use time lasting, has good acidproof, anti alkali, anti chemical flux properties, and wear resistance, easy cleaning. Conductive mat is made of high quality conductive materials, synthetic rubber.
The material and the characteristics of the crystal table mat. Come and learn about: first we know oh, soft glass, also known as the crystal plate: is a new generation of high-tech products, it replaces the traditional glass heavy fragile, wounding disadvantage outside it has a lot of advantages.
It is suitable for the dining table, desk, desk, bedside table and all the table. The high degree of transparency, and can heat the soup, tea, cold resistance, weight, non-toxic and tasteless, green environmental protection.
After scientific design, the use of imported PVC new health and environmental protection materials.
The characteristics of high resilience and high resistance to compression and compression can be suitable for a variety of environments.
It has the characteristics of non toxic, soft and transparent, safe insulation, easy cleaning and so on.
The overall heat deformation, high temperature resistance, chemical stability, non stick paint, aging is not easy.
Crystal board can be quite furniture long service life; effectively prevent burns, cuts, scratches and other external damage, make your furniture gets more effective protection.
A glass plate is pressed on a lot of desk, which is convenient for writing. Now, a new type of material is soft glass instead of glass become the people's favorite. At work, it is widely used in electronics, chemistry, pharmacy, food factory, garment factory, working platform, the surface of a variety of office machines, etc.. Family life, it is widely appeared in the glass surface, can not only reflect the true nature of the glass, fashion, and can prevent the glass furniture surface scratch.
Table mat/pvc mat made of material
1) material: PP/PVC
2) material: soft PVC
3) material SBR PVC/PP+EVA/ or natural rubber, etc
4) material: soft glass
5) PVC foaming [1]
6) material: crystal plate
9) material: chemical fiber
10) material: Plush
Role of table mats
In daily life, table mats to the people's life brings convenience, for example, can be used in the table, table, desk pad can not only protect desktop is not hot imprint, is not hot off color and hands up will give a person a kind of comfortable feeling, in addition to the dinner table can also be used for desk, coffee table, a few party, desk, ark of the head of a bed, as long as the table, can use table mat.
Pvc Placemat,Pvc Dining Mat,Pvc Table Mat,Pvc Table Pad,PVC Mat
HEBEI GEMMY IMP.& EXP.CO.,LTD , https://www.gemmycandles.com